Analysis of the work of steps using the eccentricity limiter for drilling wells with a diameter of 393,7 mm

Authors

  • I. V. Voievidko Ivano-Frankivsk National Technical University of Oil and Gas, 15 Karpatska Street Ivano-Frankivsk Ukraine, 76019
  • А. І. Riznychuk Ivano-Frankivsk National Technical University of Oil and Gas, 15 Karpatska Street Ivano-Frankivsk Ukraine, 76019
  • V. V. Tokaruk Ivano-Frankivsk National Technical University of Oil and Gas, 15 Karpatska Street Ivano-Frankivsk Ukraine, 76019
  • I. Yu. Piruh Ivano-Frankivsk National Technical University of Oil and Gas, 15 Karpatska Street Ivano-Frankivsk Ukraine, 76019

DOI:

https://doi.org/10.31471/1993-9868-2021-2(36)-23-30

Keywords:

design technique, axial load distribution, two rock-destroying elements, expander, geological factor, well curvature, eccentricity.

Abstract

Based on the results of the analysis of theoretical and practical studies of drilling large diameter boreholes, a method is proposed for designing the bottom hole assembly with two rock cutting tools, taking into account geological and technical factors that influence the formation of the well trajectory. Prospects for controlling the direction of the wellbore are substantiated using the limiter of the eccentricity value. The calculation of double-hole assemblies of the bottom of the drill string with different diameters of eccentricity limiters, allowing to achieve eccentricities of 10 mm, 20 mm, 30 mm and 40 mm has been performed. The analysis of the operation of the mentioned bottom hole assemblies when drilling a well to a depth of 900 m is carried out. The analysis is carried out in the field of construction of deep boreholes of large diameter and the efficiency of drilling a pilot hole of a smaller diameter with simultaneous formation of the final diameter using a reamer is substantiated. A brief analysis of modern foreign and domestic studies and publications related to the expansion of the pilot wellbore is presented, as well as the influence of the expansion eccentricity on the elastic-deformation state of the BHA and, as a result, on the deviation of the well is considered. A conclusion is made about the possibility of using the phenomenon of eccentric expansion to control the trajectory of the wellbore. The graphical dependences of the change in the intensity of the borehole deviation during deepening using the eccentricity of the limiter for a specific BHA, including a bit with a diameter of 295.3 mm and a reamer with a size of 393.7 mm, are shown. It is shown that with this type of arrangement at different values ​​of eccentricities, it is possible to achieve the intensity of borehole curvature in the range from 0 deg/10 m to 0.44 deg/100 m, 0075, indicating a change in the direction and magnitude of eccentricity during drilling. The graphical dependences of the change in the zenith angle of the well when deepening it for the assembly of the bottom of the drill string with different diameters of the eccentricity limiter are given. The graphical dependencies indicate that when using stops of different sizes, which make it possible to control the eccentric displacement of the reamer at the final drilling depth of a section of 500 m, it is possible to reduce the increase in the zenith angle of the well from 17.5 degrees to 10 degrees. It is concluded that by using the limiters of the eccentric displacement of the expander relative to the pilot borehole, it is possible to control the deviation of the well during the construction of conditionally vertical and inclined sections.

References

Burimov Yu.G. Kopyilov A.S., Orlov A.V. Burenie verhnih intervalov glubokih skvazhin bolshogo diametra. M.: Nedra, 1975. 231 p. [in Russian]

Voevidko I. V., Riznyichuk A. I., Martsynkiv O. B., Stetsyuk R. B. Issledovanie kinematiki i zakonomernosti iznosa rabochih organov sharoshechnyih kalibruyuschih ustroystv. Vestnik Belorussko-Rossiyskogo universiteta. Mogiliov. Respublika Belarus. 2021. No 1(20). P. 5 – 12. [in Russian]

Voevidko I.V., Tokaruk V.V. Razrabotka komponovok niza burilnoy kolonnyi dlya bureniya uslovno vertikalnyih skvazhin diametrom 660mm. Vestnik Belorussko-Rossiyskogo universiteta. 2018. No 1. P. 112-120. [in Russian]

Voievidko I.V. Rozrobka naukovo-metodychnykh osnov ta tekhnichnykh zasobiv dlia pidvyshchennia tochnosti provedennia naftohazovykh sverdlovyn v zadanomu napriami. Dysertatsiia … dokt. tekhnichnykh nauk. Ivano-Frankivsk, 2007. 353 p. [in Ukrainian]

Voievidko I.V., Tokaruk V.V., Bodzian M.A. Proektuvannia komponovok nyzu burylnoi kolony z dvoma porodoruinivnymy instrumentamy dlia burinnia sverdlovyn v zadanomu napriamku. Rozvidka ta rozrobka naftovyh і gazovyh rodo-vyshch. 2018. No 2 (67). P. 14-20. [in Ukrainian]

Gulizade M.P., Mamedbekov O.K. RaschYot tempa prostranstvennogo iskrivleniya naklonnyih skvazhin pri burenii neorientiro-vannyimi KNBK. Teoriya i praktika bureniya naklonnyih skvazhin. Baku: Izd. AzINEFTEHIMa, 1982. Vol.1. 63 p. [in Russian]

Rayhert L.A., Fryiz I.M. Napravlenoe burenie skvazhin v anizotropnyih porodah rotornyim sposobom stupenchatyimi KNBK. Trudyi VNIIBT. 1985. Vol. 61. [in Russian]

Tokaruk V.V. Udoskonalennia teoretychnykh zasad i tekhnichnykh zasobiv dlia provedennia spriamovanykh sverdlovyn velykoho diametru. 2019. PhD Thesis. Ivano-Frankivskyi natsionalnyi tekhnichnyi universytet nafty i hazu. [in Ukrainian]

Fryiz I. M. Razrabotka stupenchatyih komponovok dlya bureniya vertikalnyih skvazhin v anizotropnyih porodah: na primere mestorozhdeniy Prikarpatya : dissertatsiya na soiskanie uchenoy stepeni kandidata tehnicheskih nauk. Moskva, 1986. 211 p. [in Russian]

Hrechin E.H. Raschetyi neorientiruemyih komponovok dlya bureniya naklonnyih i horizontalnyih skvazhin. Tyumen: Neftenazovyiy universitet, 2006. [in Russian]

Shreyner L.A. Fizicheskie osnovyi mehaniki gornyih porod. M.: Gostoptehizdat, 1950. 211p. [in Russian]

Yanturin R. A. Sovershenstvovanie metodov raschetov parametrov komponovok niza burilnoy kolonnyi i ih elementov dlya bezorientirovannogo bureniya: diss. na soiskanie uchenoy stupeni kandidata tehnicheskih nauk. Ufa, 2005. [in

Russian]

Yaremiychuk R.S., Rayhert L.A. Burenie stvolov bolshogo diametra. M.: Nedra. 1977.

p. [in Russian]

Published

29.12.2021

How to Cite

Voievidko, I. V., Riznychuk А. І., Tokaruk, V. V., & Piruh, I. Y. (2021). Analysis of the work of steps using the eccentricity limiter for drilling wells with a diameter of 393,7 mm. Oil and Gas Power Engineering, (2(36), 23–30. https://doi.org/10.31471/1993-9868-2021-2(36)-23-30

Issue

Section

SCIENTIFIC AND TECHNICAL PROBLEMS OF PETROLEUM ENGINEERING

Most read articles by the same author(s)