DEVELOPMENT OF DOWNHOLE PACKER TO TEST WELLHEAD AND BLOWOUT EQUIPMENT

Authors

  • М. А. Дорохов Полтавський національний технічний університет іменіЮрія Кондратюка; м. Полтава, пр. Першотравневий, 24, тел. (050) 6317980,
  • І. В. Костриба ІФНТУНГ, 76019, м.Івано-Франківськ, вул. Карпатська, 15, тел. (03422) 42264
  • О. В. Ущенко Полтавська воєнізована частина по попередженню і ліквідації відкритих нафтових і газових фонтанів ПАТ «Укрнафта»; м. Полтава, вул. Ливарна, 10

Keywords:

wellhead and blowout equipment, pressurization capability, wellhead test packer, self-sealing cuff, contact pressure.

Abstract

ipment after installation of the latter at the well. It also explains the most common design of the wellhead packer of the UVCh type produced by the special emergency rescue service “LIKVO”, PJSC “Ukrhazvydobuvannia”. The influence of pressurization capability of the packer seal assembly on the quality of the wellhead and blowout equipment testing process was mentioned. The packer design shortcomings presented in the article were analyzed. There was also conducted an analysis of some foreign and domestic publications and studies, which showed an absence of the systematic approach to designing of the self-sealing cuffs of wellhead packers. A number of topical scientific and practical problems in the context of cuffs designing were formulated. The article also explains the main stages and results of the experimental studies of the dependence of contact pressures on the mating surface “cuff – casing” on the most influential factors. The stages and results of computer modeling of the stress-strain state of the base and improved cuffs with the account of the most influential factors were described. Based on the study results, there was described an improved design of the wellhead test packer produced by Poltava militarized unit for prevention and
elimination of open oil and gas flows, PJSC “Ukrnafta”, with indication of operations order and design features.

References

1 Костриба І.В. Підвищення рівня фонтанної безпеки в процесі ремонту газових свердловин [Текст] / І.В. Костриба, Х.А. Бойкович : Матеріали Міжнародної науково-технічної конференції «Нафтогазова енергетика 2015», 21-24 квітня 2015 р. : Тези доповідей. – Івано-Франківськ. – 2015. – С. 45 – 47.
2 Износ и защита обсадных колон при глубоком бурении [Текст] / М.Л. Кисельман. – М.: Недра, 1971. – 210 с.
3 Яковлев А. С. Исследование работы манжетных уплотнителей пакеров в режиме саомуплотнения [Текст] / А.С. Яковлев, С.С. Яковлев // Строительство нефтяных и газовых скважин на суше и на море. – 2006. – № 9. – С.44 – 46.
4 Ледяшов О.А. Пакеры для опрессовки устья скважин типа ПОУ [Текст] / О.А. Ледяшов, В.Г. Никитченко, Е.Н. Штахов // Строительство нефтяных и газовых скважин на суше и на море. – 2008. – № 1. – С.25 – 27.
5 Римчук Д.В. Нові технічні засоби ДП «ЛІКВО» для забезпечення фонтанної та газової безпеки під час буріння та капітального ремонту свердловин [Текст] // Нафтогазова галузь України. – 2015. – № 6. – С.37 – 40.
6 Buyalich G. D. Modeling of Hydraulic Power Cylinder Seal Assembly Operation [Text] / G. D. Buyalich, K. G. Buyalich // Presented at Mining 2014: Taishan Academic Forum – Project on Mine Disaster Prevention and Control: Chinese Coal in the Century: Mining, Green and Safety, China, Qingdao, 17–20 October 2014. – Amsterdam – Paris – Beijing: Atlantis Press, 2014. – P. 167–170.
7 Boart P. On the Normal Stress Effect in Grease-Lubricated Bearing Seals [Text] // P. Boart, M. Lugt, B. Procash // Tribology Transactions. – 2014. – Vol. 57. – Issue 5. – P. 939 – 943.
8 Gölz J. Experimental Study on the Sealing Mechanism of Bidirectional PTFE Lip Seals [Text] // J. Gölz, F. Bauer, W. Haas // Tribology Transactions.– 2014. – Vol. 57. – Issue 5. – P. 866 – 870.
9 Huang Y. Simulation of the Effects of a Plunge Ground Rod on Hydraulic Rod Seal Behavior [Text] // Y. Huang, R. Slant // Tribology Transactions. – 2013. – Vol. 56. – Issue 6. – P. 986– 996.
10 Dorokhov M.A. Experimental research of the process of probationary self-sealing packer during
the construction of oil and gas wells / M.A. Dorokhov, I.V. Kostriba, V.O. Betsun V.О., I.V. Piienko // International Journal of Applied Science and Engineering Research. – Radom, Poland. – 2015. – Vol. 2.
11 Cергєєв П.В. Комп’ютерне моделювання технологічних процесів переробки окрисних копалин (практикум) [Текст] / П.В. Сергєєв, В.С. Білецький. – Маріуполь: Східний видавничий дім, 2016. – 119 с.
12 Дорохов М. А. Чисельний метод у дослідженні вузлів ущільнень випробувальних свердловинних пакерів / М. А. Дорохов // Матеріали 68-ї наукової конференції професорів, викладачів, наукових працівників, аспірантів та студентів Полтавського національного технічного університету імені Юрія Кондратюка, 19 –22 квітня 2016 р.: тези доповідей. – Полтава, 2016. – С. 54 – 57.

Published

27.05.2016

How to Cite

Дорохов, М. А., Костриба, І. В., & Ущенко, О. В. (2016). DEVELOPMENT OF DOWNHOLE PACKER TO TEST WELLHEAD AND BLOWOUT EQUIPMENT. Oil and Gas Power Engineering, (1(25), 12–21. Retrieved from https://nge.nung.edu.ua/index.php/nge/article/view/352

Issue

Section

PHYSICAL-TECHNICAL PROBLEMS OF ENERGY CARRIERS RECOVERY